Introduction:
Japan A&D has produced a high-precision rapid moisture analyzer with a brand-new design concept and superb process technology. It is simple to operate, easy to observe, and is fully used in food, tobacco, pharmaceuticals, petroleum, paper, feed, and chemical industries with its excellent performance. , Coatings, minerals, environmental protection, geology and other industries to quickly determine the moisture content of materials, while meeting the measurement requirements of solid, particle, powder, colloidal and liquid moisture content
Features:
●Fast and uniform halogen lamp heater with innovative SRA technology
Straight tube halogen lamp and uniquely designed SRA (Secondary Radiation Auxiliary Device) radiator are used to shorten the measurement time and form a fast and uniform heater.
●Height
The use of SHS's fast and sensitive load cell enables very small samples to be measured with very high moisture content under high-precision weighing.
●Using sodium tartrate dihydrate as the standard for checking the accuracy of water content measurement
Sodium tartrate dihydrate is a chemical substance with a stable water content of 15.66%+0.3/-0.1, so it can be trusted for degree inspection and supplied to the analyzer as a reference value.
●Heater temperature calibration (MS/MX only)
Optional temperature calibrator, calibration results can be output in GLP, GMP, ISO format.
●Standard WinCT-Moisture software (MS/MX only) to realize real-time graphic display
WinCT-Moisture software is a moisture content analysis software designed for graphic display. It can display the graph of the change of moisture content during measurement, and can set the measurement program of different samples through computer-assisted analysis based on this graph.
●Measurement program, measurement result storage function
More than 20 groups of measurement programs can be stored, and different measurement programs can be called to determine the moisture content at any time according to different samples. Therefore, it can achieve fast measurement and avoid setting operation errors (more than 10 groups for MF and 5 groups for ML). The measurement results can be stored in 100 groups (50 groups for MF and 30 groups for ML) and output through a computer or printer. Human errors are completely avoided.
●Comply with GLP/GMP/GCP and ISO standards, with date/time, ID, calibration data and test record output
It can record and output calibration data and measurement data to meet quality management and certification requirements.
●Standard RS-232 interface
Two-way communication with PC or connection to printer.
●Clear and easy to observe large-screen fluorescent display
The measurement program, set value, moisture content change rate, measurement status, data number and other important information are displayed clearly at a glance.
●Easy to operate parts
The ergonomically designed tray handle avoids accidents such as burns when hot samples are put in or taken out. The wing-shaped handle makes the heating cover easy to open and close.
●Guarantee of low maintenance cost
The user does not need to stop when replacing the halogen lamp, and the protected chamber is easy to clean (the life of the halogen lamp is about 5000 hours)
●Five measurement procedures
Standard mode: The measurement is automatically completed by setting the high, medium and low measurement degrees.
Automatic mode: When the water content change rate is less than a set rate, the measurement is automatically ended.
Quick mode: In order to achieve rapid measurement, heat at 200°C for the first 3 minutes after starting, and then complete the measurement according to the automatic setting.
Timing mode: complete the measurement by setting the duration.
Manual mode: Operate the measurement process by pressing the start and stop keys.
●Four drying programs
Standard drying: After starting, the temperature is raised directly to the set temperature.
Gradually dry: After a preset time, the temperature is gradually increased to the set temperature.
Step drying: adopt different temperatures in stages according to time.
Quick drying: After rapid heating at 200℃ for 3 minutes, it will continue to heat according to the set drying temperature.
Any combination of measurement procedures and drying procedures can fully meet the determination requirements of different samples.
Standard accessories
●Sample tray (20 for MS/MX/MF, 10 for ML)
●Plate handle (2 for MS/MX/MF, 1 for ML)
●Tweezers, sample spoon and test sample (sodium tartrate dihydrate 30g) (MS/MX/MF only)
●CD-ROM (MS/MX is WinCT-Moisture, MF is WinCT)
●MS/MX is equipped with RS-232 line,
●Display film
●Dustproof film (MS/MX/MF only)
●User Manual
●Quickly check the card
●Power cord
●Two fuses
Optional accessories:
●AX-MX-31 sample tray (100 pcs)
●AX-MX-32-1 glass fiber sheet (100 sheets)
●AX-MX-32-2 glass fiber sheet (100 sheets)
●AX-MX-33 test sample (12 pieces of 30g sodium tartrate dihydrate)
●AX-MX-34 Halogen Tube
●AX-MX-40 RS-232 cable
●AX-MX-41 calibration weight (20g, OIML)
●AX-MX-43 temperature calibrator
Model | MS-70 | MX-50 | MF-50 | ML-50 |
Heating source | 400W halogen lamp | 400W halogen lamp | 400W halogen lamp | 400W halogen lamp |
Weighing range | 71g | 51g | 51g | 51g |
Reading accuracy | 0.0001g | 0.001g | 0.002g | 0.005g |
Water content Measurement accuracy | 0.001/0.01/0.1% | 0.01/0.1% | 0.05/0.1/1% | 0.1/1% |
Temperature preset range | 30-200℃ | 50-200℃ | 50-200℃ | 50-200℃ |
Moisture content Display mode | Relative moisture content, moisture content, dry-wet ratio, wet-dry ratio
| |||
Measurement method | standard, automatic, timing, manual | |||
Weighing pan size (mm) | Diameter 85 | |||
Dimensions W×D×H（mm） | 215 x 320x 173 | |||
Weight (about Kg) | 6.0 | 6.0 | 6.0 | 6.0 |
